CUSTOM CUES - CUE REPAIR - CUE CONSIGNMENT - SINCE 2013

• All original Franklin Era Gaboon Ebony nose 
• SW Cue #95-389
• Very good used condition for its age, just a few bumps here and there
• All is straight together and apart 
• 6 Birdseye Maple points 3hi/3lo
• 2 Veneers of maple and red 
• SW Birdseye maple segment in the butt sleeve
• SW red & maple stitched veneer ringwork at the butt cap, joint as well as the shaft collars
• Black with white specs Irish linen wrap
• Black phenolic butt cap & joint collars
• Gaboon Ebony forearm
• Gaboon Ebony butt sleeve
• Brass SW custom 3/8x11 joint pin 
• Butt is 28.75" & 16.55oz
• Shaft 1 is 29.25" & 3.19oz
• Ferrule 1 is white micarta & 12.6mm
• Shaft 2 is 29.25" & 3.19oz
• Ferrule 2 is white micarta & 12.5mm

• Excellent condition
• Straight together and apart
• This is an earlier made SS 1/2" joint known to be one of the best playing joints
• Full compression joint AKA Dennis' "squeeze fit" joint 
• Ivory ferrules
• Ivory "Rambo Ring" at the butt cap
• 4 Sharp and ling half spliced rosewood points (not a full splice/sneaky)
• Straight grain maple forearm
• Rosewood butt sleeve
• Black with double white specs Irish linen wrap 
• Phenolic thin collars above and below the wrap
• Black phenolic short butt cap
• Black phenolic joint collars on the butt and shafts
• Stainless steel half joint & 5/16x14 joint pin
• Butt is 29" & 14.0oz
• Shaft 1 is 29" & 4.2oz
• Ferrule 1 is ivory & 13mm
• Shaft 2 is 29" & 3.7oz
• Ferrule 2 is ivory & 12.5mm

For sale is a VERY interesting patriotic cue by Bill Schick with original scrimshaw artwork. This cue was ordered prior to 9/11/01 and was finished 3/11/02. The gentleman that ordered the cue worked in finance in NYC in the WTC Tower #1. On September 11th, 2001 the owner of this cue was working in Tower #1 of the World Trade Center all the way up on the 83rd floor when the first plane crashed into his tower (tower #1). He was fortunately able to escape the building by foot down 83 flights of stairs. During his escape tower 2 was struck and had fallen while they were going down the flights of stairs which he did not know until he was outside of tower 1. When Bill found out that the customer that ordered this cue had survived September 11th and was able to escape and survive, he added the scrimshaw artwork of the American eagle with a teardrop from its eye with the words "PAYBACK IS HELL" on each side inside the ivory design inlay panel with brass rings on each side as a beautiful gesture to the owner. Please see LOA in the photos for Bill's personal notes on this cue. 

• 64 Inlays of ivory, brass with original scrimshaw work by Bill Schick
• All original, this cue has been used but is still in very good condition, there are some finish bumps and some oxidation of the brass rings at the joint but overall in very good condition
• Straight together and apart
• Ivory joint 
• Ivory inlays
• Ivory tipped pin
• Ivory ferrules
• 4 Nicely figured Rosewood points
• 3 Veneers of black, mahogany & white 
• Each of the points contains a classic design of a sharp notched diamond with a dot above & two below
• Very nicely figured Birdseye Maple forearm 
• Nicely figured rosewood butt sleeve 
• The butt sleeve contains two large panels of ivory with outlined scrimshaw, brass rings, an American Eagle scrimshawed with a teardrop from its eye with the words "PAYBACK IS HELL" as well as brass circles inlayed & two set s of large sharp notched diamonds with a dot above & below in between the larger panels
• Traditional Delrin butt cap with "Schick 3-11-02" engraved
• Brown smooth leather wrap 
• Brown Micarta joint collars with twin brass ringwork at the joint & shaft collars
• Capped ivory joint with brass 3/8x10 pin 
• Butt is 28.75" & 15.55oz
• Shaft 1 is 28.75" & 3.81oz
• Ferrule 1 is ivory & 13.1mm
• Shaft 2 is 28.75" & 3.77oz
• Ferrule 2 is ivory & 12.9mm

• 2007 Made cue
• 92 Total inlays of ivory & silver 
• All white is ivory
• This cue is dead straight together and apart 
• The finish could use a refinish as it has been used and has a some signs of wear mainly on the butt cap and butt sleeve, nothing major at all
• Ivory points
• Ivory joint
• Ivory butt cap
• Ivory ferrules 
• Ivory inlayed rings
• Signed "Ariel Carmeli 3-07" on the bottom of the butt cap
• 6 Points 3hi/3lo 
• The tall points are ivory 
• Each of the tall points contains a sharp silver fancy diamond
• The short points are Gaboon Ebony
• The tall points have 2 veneers of maple and teal color
• The short points have 3 veneers of maple, teal & maple
• Gaboon Ebony forearm
• Gaboon Ebony butt sleeve 
• The butt sleeve contains a load of sharp inlayed silver and ivory that make 4 sets of inlay patterns around the sleeve
• Twin silver rings at all locations with fancy diamonds of ivory inlayed around each set
• Black Irish linen wrap 
• Modified 3/8x10 joint pin 
• Butt is 29" & 14.9oz
• Shaft 1 is 29.25" & 4oz
• Ferrule 1 is ivory & 13.2mm
• Shaft 2 is 29.25" & 4oz
• Ferrule 2 is ivory & 12.8mm

• Excellent condition
• 60 Total inlays of ivory
• Each of the 4 points contains a notched ivory diamond as well as two dots below and one above
• The butt sleeve contains 4 sets of 4 ivory notched diamonds that create 4 larger diamonds as well as numerous ivory dots above, below as well as in between the larger inlay patterns
• Ivory joint
• Curly Maple forearm
• 4 Points of Gaboon Ebony
• 4 Veneers of black, navy blue, olive and maple 
• Gaboon Ebony butt sleeve 
• Melamine butt cap with AC logo engraved into it
• Black bull wrap perfectly installed
• Black phenolic joint collars with single silver rings on the butt and shafts
• Stainless steel 3/8x10 joint pin
• Butt is 29" & 15.3oz
• Shaft 1 is 29" & 4.0oz
• Ferrule 1 is ivory & 12.9mm
• Shaft 2 is 29" & 3.8oz
• Ferrule 2 is ivory & 12.85mm

• Excellent barely used condition, one shaft has some finish pop at the edge but otherwise the entire cue is in perfect condition
• Ivory tipped pin with Schick "S" engraved on top'
• 1998 Made cue
• 20 Ivory inlays
• Birdseye Maple forearm
• 4 Points of ebony
• 4 Veneers of black, orange, green & maple  
• Each of the 4 points contains an ivory diamond
• Figured Ebony butt sleeve
• The butt sleeve contains 4 sets of 3 ivory diamonds with ivory dots in between
• Twin silver rings at all locations including the shaft collars in black phenolic collars
• Black with white specs Irish linen wrap
• Traditional 1.5" Delrin butt cap with Schick 1998 engraved  
• Stainless steel joint & 3/8x10 pin
• Butt is 29" & 16.98oz
• Shaft 1 is 29" & 3.79oz
• Ferrule 1 is ivory & 13.15oz
• Shaft 2 is 29" & 3.72oz
• Ferrule 2 is ivory & 13.15mm

Here is an excellent cue by Anthony Milanesi that worked along side Tony at Black Boar. This cue has a perfect fit and finish and feels great in the hand. Anthony's cues will be even more sought after in the future and I am sure he will or already has a lengthy wait for a cue... 

• Excellent condition
• Straight together & apart
• Gaboon Ebony forearm
• 6 Holly recut points 3hi/3lo
• 6 More points are cut into the Holly points of very figured Cocobolo
• Very figured Cocobolo butt sleeve
• Perfectly indexed Cocobolo butt cap matched to the butt sleeve
• Ivory Hoppe ring with silver rings on each side
• Thin silver rings with white ring in between
• Black phenolic joint collars on the butt and shafts
• Perfectly matched Lizard wrap
• Ivory over steel joint with 5/16x14 joint pin
• Butt is 29" & 15.1oz
• Shaft 1 is 29" & 4.0oz
• Ferrule 1 is LBM & 12.8mm
• Shaft 2 is 29" & 4.0oz
• Ferrule 2 is LBM & 12.8mm

• Very good condition, only a few minor bumps in the finish, all original
• Early made cue, I believe 1980-1986
• Early TS logo
• Rare Cocobolo cue
• Rare Cocobolo joint
• Ivory Hoppe ring
• 12 Large, medium and small inlays of ivory
• This is a 4 point cue but the points are "ghost points" as they are a wood of very similar color
• Each of the 4 points contains a medium ivory diamond as well as ivory spears atop each point
• The butt sleeve contains 4 large ivory diamonds 
• Dark Cocobolo butt sleeve
• Dark Cocobolo forearm
• Black phenolic butt cap
• Black phenolic joint collars
• 4 Points of Paduk (I believe, hard to tell) 
• Black with white specs Irish linen wrap
• Cocobolo joint & 5/16x14 pin
• Butt is 29" & 15.77oz
• Shaft 1 is 29" & 3.63oz
• Ferrule 1 is LBM & 12.6mm
• Shaft 2 is 29" & 3.56oz
• Ferrule 2 is LBM & 12.4mm

• BRAND NEW UNCHALKED CONDITION
• 28 Total inlays of Supertusk 
• Inlayed ringwork (8 count) at the joint & shaft collars with silver rings above & below
• Gaboon Ebony butt sleeve
• Gaboon Ebony forearm
• 4 Half spliced points of Gaboon Ebony
• 4 Veneers of maple, blue, magenta & maple
• Each of the 4 points has a fancy diamond inlayed 
• Supertusk joint 
• Supertusk Hoppe ring 
• Black leather lizard wrap 
• Black phenolic butt cap
• AC logo on the butt cap
• Black phenolic joint collars
• Stainless steel Modified 3/8x10 joint pin 
• Butt is 29" & 15.02oz
• Shaft 1 is 29" & 4.05oz
• Ferrule 1 is Juma & 13mm
• Shaft 2 is 29" & 3.88oz
• Ferrule 2 is Juma & 13mm

• Brand new & unchalked condition 
• Premium Rounceville blank 
• Full splice construction
• 4 Veneers between the splice of dark purple, magenta, dark brown & maple 
• Very figured Snakewood fully spliced into very figured Birdseye Maple
• Custom billet ringwork of pink, purple & black billet at the butt cap, joint & shaft collars with silver rings 
• Black phenolic butt cap and joint collars 
• Red G10 modified 3/8x10 joint pin
• Signed in gold P. Diveney "2024"   
• Butt is 29" & 15.62oz
• Shaft 1 is 29" & 3.64oz
• Ferrule 1 is Juma & 12.6mm
• Shaft 2 is Kielwood & 29" & 3.08oz
• Ferrule 2 is Juma & 12.6mm

This cue was recently in the Tad shop and Fred did confirm this is one of his father's earlier made cues and it is in all original condition and has been used but would still be a very nice addition to any collection...

• This cue is very used but we have made a concession in the price due to the condition
• The butt does have a roll at the joint but the shaft is straight
• Highly figured Birdseye Maple forearm
• Thick Delrin ring below the wrap
• The butt sleeve is Ebony with thick nickel silver rings as well as a centered stitched maple ring with black and red veneers 
• LONG white Delrin Tad style butt cap
• Black fiber collars with nickel silver rings at the joint & shaft collars
• White with green specs Irish linen wrap
• Stainless steel joint & 5/16x18 brass pin
• Butt is 28" & 15.6oz
• Shaft is 29" & 3.36oz
• Ferrule is ivory & 12.25mm

• Barely used condition, one VERY small bump on the finish in the forearm that is invisible to the eye
• 28 Total inlays 
• Signed "Gilbert 19" on the forearm
• 4 Points of Gaboon Ebony 
• 6 Veneers of black, blue, black paper, maple, black paper & green
• Each of the points contains a butterfly inlay as well as a dot above & below
• Nicely figured Birdseye Maple forearm
• Gaboon Ebony butt sleeve 
• The butt sleeve contains a medium butterfly inlays with a dot above & below as well as a dots in between
• Stitched ringwork at all locations including the shaft collars
• Black semi-smooth very lightly textured leather wrap
• White phenolic joint 
• White melamine butt cap
• Engraved Gilbert Cues bumper 
• Stainless steel 3/8x10 joint pin
• Butt is 29" & 14.82oz
• Shaft 1 is 29" & 4.03oz
• Ferrule 1 is LBM & 12.95mm
• Shaft 2 is 29" & 3.86oz
• Ferrule 2 is LBM & 12.9mm

• Used condition, has finish bumps and a few dents, could use a refinish
• The butt has a very slight roll and so do both shafts, tips does not leave the table when rolled
• This cue has a barely visible KQ logo on the end of the butt sleeve
• Ivory joint 
• This cue has a total of 32 inlays of ivory, ebony & maple (white inlays are ivory) 
• Purpleheart butt sleeve
• Purpleheart forearm
• 4 Points of Birdseye Maple 
• 1 Veneer of black
• Stitched ivory ringwork in a Purpleheart billet
• This cue has no butt cap, purpleheart all the way down to the bumper 
• Black with white specs Irish linen wrap
• Ivory piloted joint & 5/16x14 pin
• Butt is 29" & 15.41oz
• Shaft 1 is 29" & 4.27oz
• Ferrule 1 is ivory & 12.7mm
• Shaft 2 is 29" & 4.21oz
• Ferrule 2 is ivory & 12.65mm